引入气相对D类颗粒间歇卸料过程特性的影响

通过测量并分析引入气相前后D类颗粒间歇卸料过程中示踪颗粒的流动状态、压力分布和颗粒流率，发现床体内气固两相流动特性不仅随时间变化，还受到气速（正负压差）的影响。据此将卸料过程按时间分为3个阶段：初始蓄压（PS）阶段、稳定卸料（SD）阶段和非满管流（PP）阶段；并给出各卸料阶段不同正、负压差和重力条件下的气固流动特性。在时间较长、流场较为稳定的SD阶段，发现卸料口颗粒阻力是影响颗粒流率的关键参数，通过修正De Jong公式、Beverloo公式，依次建立卸料口颗粒阻力、D类颗粒卸料流率预测模型，与实验值吻合较好，有望为引入气相调控D类颗粒卸料流率的方法提供参考。     

Composite mixed matrix membranes incorporating microporous carbon molecular sieve as filler in polyethersulfone for CO2/CH4 separation

Membrane technology has been considered a key factor for sustainable growth in high-efficiency gas separation. Current mixed matrix membranes (MMMs) technology is rising, but these membranes in the dense structure are having difficulties in operating at high pressures and scale up for commercialization. The purpose of this research is to synthesize composite MMMs (CMMMs) consisting of polyethersulfone (PES), carbon molecular sieve (CMS 1–5 wt %), and Novatex 2471 nonwoven fabric (support layer). The membranes' physical, chemical, and thermal properties were evaluated by different analytical equipment. The morphology of both PES and PES-CMS composite membranes had a porous and asymmetric structure, in which CMS was uniformly distributed in the polymer matrix. The thermal properties showed that the membranes were stable up to 350 °C with a single glass transition temperature. The functional groups in the membrane were confirmed by spectral analysis. The gas performance results showed that carbon dioxide permeance increased with increased CMS concentration and methane permeance decreased due to the hindering effect of CMS under similar operating conditions. The highest selectivity achieved was 12.774 using CMMM of 5 wt % of CMS at 10 bar, which on average was 137.80%, improved selectivity compared to pure PES membrane. The support layer was able to withstand high operating pressures and showed the ability to scale up. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48476.     

RTM制备玻璃纤维增强环氧树脂复合材料的力学性能分析

以环氧树脂为基体,短切玻璃纤维和玻璃纤维布为增强材料,通过RTM工艺制备了玻璃纤维增强环氧树脂(GF/EP)复合材料,并研究了RTM工艺制备玻璃纤维布增强环氧树脂(L-GF/EP)和短切玻璃纤维增强环氧树脂(S-GF/EP)复合材料的拉伸和弯曲性能,分析了开孔对两种复合材料拉伸性能的影响。结果表明:在拉伸过程中,开孔试样因孔边产生的应力集中,导致其拉伸强度与无孔试样相比下降了30%左右;玻纤铺层类型的不同对复合材料的力学性能具有显著影响;L-GF/EP复合材料内部结构完整,在载荷作用下,复合材料的弯曲断裂呈现一定的假塑性断裂模式,达到弯曲极限挠度值后,出现一定程度的回弹现象,其力学性能优于S-GF/EP复合材料。     

Microstructure and Mechanical Properties of Cu Matrix Composites Reinforced byTiB2/TiN Ceramic Reinforcements

Cu matrix composites reinforced by TiB₂/TiN ceramic reinforcements (Cu/TBN composites) were prepared by hot pressing method. Prior to the hot pressing, Cu/TiB₂/TiN composite powders (CTBN powders), which were used as the starting materials of Cu/TBN composites, were fabricated by self-propagating high-temperature synthesis method. The CTBN particles were found to be in a special core-shell structure with a Cu-Ti alloy core and a TiB₂/TiN ceramic shell. The test results presented obvious improvements in mechanical properties. The highest ultimate tensile strength reached up to 297 MPa, 77 MPa higher than that of Cu. And the highest hardness reached up to 70.7 HRF, 15.7 HRF higher than that of Cu. A comparative study indicated that the core-shell structured particles could bring about more obvious strengthening effect than the traditional irregularly shaped particles, which was due to the improved Cu/ceramics interfacial bonding, the linkage strengthening effect of both TiB₂ and TiN, and higher load bearing ability of the core-shell structured reinforcements.     

脉冲偏压对TiAlCN薄膜结构与力学性能的影响

利用多弧离子镀-磁控溅射复合技术通过改变脉冲偏压在Si片与SS304基体表面制备了TiAlCN薄膜,研究了不同脉冲偏压对薄膜结构和力学性能的影响。薄膜成分、表面形貌、相结构及力学性能分别利用能量弥散X射线谱(EDS)、扫描电镜(SEM)、X射线衍射(XRD)和纳米压痕仪等设备进行表征。结果表明,随着脉冲负偏压的增加,薄膜中Ti元素的含量先减小后增大,而Al元素有相反的变化趋势。适当增大脉冲偏压,薄膜表面颗粒、凹坑等缺陷得到明显改善。物相分析表明TiAlCN薄膜主要由(Ti,Al)(C,N)相,Ti4N3-x相和Ti3Al相组成。薄膜平均硬度与弹性模量随脉冲负偏压的增加先增大后减小,在负偏压-200 V时达到最大值分别为36.8 GPa和410 GPa。     

TC4合金表面Cu/石墨复合镀层的摩擦磨损行为

采用无氰电镀工艺在TC4合金表面制备了Cu/石墨复合镀层，研究了镀层的组织结构和摩擦磨损行为。结果表明，采用无氰电镀方法能够在TC4合金表面制备出组织致密且与基体结合紧密的Cu/石墨复合镀层，但增加镀层中石墨的含量会降低镀层与基体合金的结合强度，并导致硬度小幅下降。摩擦磨损实验结果表明，Cu/石墨复合镀层具有优良的摩擦磨损防护性能，归因于石墨有效降低了镀层的摩擦系数和磨损率；对镀层磨损形貌、磨损产物和摩擦系数的综合分析结果表明，纯铜镀层的摩擦磨损机制主要为犁削磨损、黏着磨损和剥层磨损，Cu/石墨复合镀层的磨损机制为轻微的削层磨损和疲劳磨损。     

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

A comprehensive study of the phase composition, microstructure evolution, microhardness and wear performance of WC-12Co composite coatings fabricated by laser cladding using coaxial powder-feed mode was presented. It was shown that a combination of high scan speed and high laser energy density made WC on the edge of WC-12Co composite powders partially melt in liquid Co and 304 stainless steel matrix, and then new carbides consisting of lamellar WC and herringbone M₃W₃C (M=Fe, Co) were formed. Meanwhile, WC-12Co composite coatings with no porosity, cracks and drawbacks like decarburization were obtained, showing high densification and good metallurgical bonding with the substrate. Furthermore, a considerably high microhardness of HV_0.3 1500-1600, low coefficient of friction of 0.55 and wear rate of (2.15±0.31)×10^-7 mm³/(N·m) were achieved owing to the synergistic effect of excellent metallurgical bonding and fine microstructures of composite coating under laser power of 1500 W.     

Core–shell adsorbents by electrospun MOF-polymer composites with improved adsorption properties: Theory and experiments

A new class of core–shell adsorbents has been created by electrospun metal–organic framework (MOF) particles embedded in polymer nanofibers, which have provided many unique properties compared to the existing MOF coating technologies. For the first time, we demonstrate the improved adsorption selectivity of CO₂ over N₂ using electrospun polymer/ZIF-8 adsorbents in experiments. Furthermore, an analytical model based on the assumption that the diffusivity in core is 10 times higher than that in shell is developed to describe the theory of improved selectivity for core–shell adsorbents that is validated against a more accurate finite element model developed in COMSOL. Our model shows three regimes including exclusive shell uptake, linear core uptake, and asymptotic core uptake. These regimes are related to material properties and uptake times, which could be used as design criteria to balance core stability, maximum selectivity, and maximum uptake. An advanced HAADF STEM tomography (Movie S1 ) shows that the shell thickness in the case of polymer/ZIF-8 is on the order of 10 nm, allowing the regime of maximum selectivity to be realized. Kinetically limited adsorption tests at 45°C demonstrate that these composite fibers can perform in a regime of selectivity and uptake for the separation of CO₂ and N₂ that is unobtainable by either the MOF or fiber independently, showing a great potential for postcombustion CO₂ capture.     

Unraveling the film-formation kinetics of interfacial polymerization via low coherence interferometry

Interfacial polymerization (IP) is one of the most important methods for fabricating thin film composite (TFC) membranes. Understanding the film-formation mechanisms is of great value for developing membranes with enhanced performance. This work proposed a novel method to in situ characterize the film-formation kinetics via low coherence interferometry (LCI). The polyamide film formed at the liquid–substrate interface was scanned in real time; the polymerization induced significant variations in the optical properties around the reaction zone. After mitigating the effects of the perturbed interface, the surface-averaged intensity profiles provide a solid basis for analyzing the film-formation kinetics at various depths. In particular, the effects of the monomer concentrations were investigated to reveal the asymmetric growth and development of irregular substructures. All the characterization results confirm that the LCI-based characterization is a powerful tool for studying the structural evolution of the IP layer and thereby providing deeper insights for optimizing TFC membranes.     

Simultaneous accommodation of Dy3+ at the lattice site of β-Ca3(PO4)2 and t-ZrO2 mixtures: Structural stability,mechanical, optical,and magnetic features

Structurally stable β-Ca₃(PO₄)₂/t-ZrO₂ composite mixtures with the aid of Dy³⁺ stabilizer were accomplished at 1500°C. The precursors comprising Ca²⁺, P⁵⁺, Zr⁴⁺, and Dy³⁺ have been varied to obtain five different combinations. The results revealed the fact that complete phase transformation of calcium-deficient apatite to β-Ca₃(PO₄)₂ occurred only at 1300°C, whereas the evidence of t-ZrO₂ crystallization is obvious at 900°C. The dual occupancy of Dy³⁺ at β-Ca₃(PO₄)₂ and t-ZrO₂ structures was evident; however, Dy³⁺ initially prefers to occupy β-Ca₃(PO₄)₂ lattice until its saturation limit and thereafter accommodates at the lattice site of ZrO₂. The typical absorption and emission behavior of Dy³⁺ were noticed in all the systems and, moreover, the surrounding symmetry of Dy³⁺ domains has been determined from the luminescence study. All the systems ensured paramagnetic response that is generally contributed by the presence of Dy³⁺. A gradual increment in the phase content of t-ZrO₂ in the composite mixtures ensured a significant improvement in the hardness and Young's modulus of the investigated compositions.